Собственно, когда началась эта планшетная лихорадка, я себе раздобыл flytouch II из Китая. Но кроме как посмотреть раз в месяц что-то мозгоразжижающее его не юзал. Разве что разок в виде навигатора. Потом пришла в голову мысль, а ну как там удобно даташиты смотреть. Увы нет. Ищет в пдфах медленно, так как адобридер на андройде тормознутый. […]
-
-
Porting OpenWRT to an unbranded 3GN router
Ok, not porting, but more like adding support for the board, ’cause the chip is already quite known. I got this thing from my favourite place to waste money – DX. It has RTL3050F inside, 32MB RAM, 4MB FLASH, and runs at 320Mhz. A good bonus is a usb host and a usual uart, well […]
-
ee-locket
Well, I really wanted to make my own version of a locket with leds, as seen on HaD some time ago. So I ordered some lockets as soon as I could. However, the seller did include a smaller locket as a gift…. And I couldn’t think of a use for it… Well, until I gave […]
-
Necromant’s MultiDrop UART: The software.
Well, there were quite a few bugs in the device and it looks like the baseboard is going to be redesigned, although it will still be compatible with all the extension ‘shields’. It looked like the transistors gave a .2 volts voltage drop, and the diodes dropped 0.1 more, turning regulated 3.3 into 3.0 volts, […]
-
Necromant’s MultiDrop UART: The Baseboard
I work with a lot of different embedded boards. Most of them have linux installed. And what do these have in common? Yep. UART. The thing you use to debug them, send uboot parameters and etc. When there are a plenty of boards around, you tend to have a pile of usbuart chips around, your […]
-
Creating .libs for kicad/eeschema semiautomatically
Well, everyone has to eventually make one. Since we have a cool online utility from C. Rohrbacher http://kicad.rohrbacher.net/quicklib.php this is quite simple. Just fill in all the pins, orient them and you are ready to go… But if there are over 200 pins, this is getting tiresome. When I was making a lib for at91rm9200 […]
-
Готовим фотошаблоны печаток из kicad’a при помощи latex
Если вы начинали со Sprint Layout, то наверное помните диалог печати, который позволяет совместить на листе сколько-то копий одной и той же платы. К сожалению, одной единственной или одного и того же слоя. В kicad’е нет и этого. Если плата здоровая, а изготавливать с первого раза уже получается почти всегда, то это нормально. Но если […]
-
USB Sniffo dongle
Well, another weekend, and another project. This time, once I got to my lab, I had to debug a DIY usb dongle (avr based, stuffed with vusb framework). And… Well, things didn’t work out of the box this time and I got a bunch of glitches. So, I decided to finally make a dongle for […]
-
A bit of necromancy: resurrecting an HSDPA modem
Well, to make the long story short – it’s dead. I was setting up my router with OpenWrt to share the internet, and connected the wrong power supply unit that provided 7.5 instead of 5 volts. The router is ok – there’s a good stepdown converter onboard, while the usb host is directly powered by […]
-
the_dropper
I urgently needed a small device, to produce me a number of fixed voltages (mostly below 3.3 volts). I was a bit too lazy to do the step-down, so I resorted to lowdrops. You know, the guy who borrowed my L-meter for a ‘week or so’ still didn’t return that, and I do not feel […]