Skip to content
Necromancer's notes
  • Contact
  • Remote-flashing an AVR board from an ARM

    27.02.2011 ncrmnt

    Okay, I admit it, we’re building something quite big this time. And robotic. So big, that it needs some embedded brains of the ARM scale (SmartQ7) and a microcontroller, that does all the dirty work (e.g. controls motors, gathers data from sensors and feeds that stuff to an ARM for processing.) However, disconnecting the micro […]

  • A bit of Necromancy: resurrecting a TRENDnet router

    15.01.2011 ncrmnt

    I got this one for free from a friend a long time ago. Looks from inside like it had been used in a bucket of water a wet environment. I just needed a router urgently and was a bit too lazy to run out to get a new one, so I decided to fix this […]

  • Chinese HSDPA modem & linux support

    31.12.2010 ncrmnt

    Okay, I hacked it to work. So, what was the problem? These damned modems by default show up as a mass_storage. As a cdrom actually. Which contains drivers. For windows. Afterwards they are switched into a regular modem mode, which linux can make use of. To do the switch in linux we need usb-modeswitch. A […]

  • SmartQ7 vs CO2 laser.

    11.12.2010 ncrmnt

    So, time to get my SmartQ ready to serve as a robobrain. So I needed a way to connect to the internal UART. Luckily with access to a laser cutter it’s really simple… Thanks to Dmitry for the assistance with the cutter. The pin header contains Vcc in for battery charger, regulated 3.3 volt output, […]

  • Chinese InfoTM X220 based tablet.

    11.12.2010 ncrmnt

    So, I finally got that one. Took 22 days for it to get here. I remember the bunch of bugs SmartQ7 came along with, so I got myself morally prepared for several days of making different things work. Surprisingly – that wasn’t really needed. The touchscreen is resistive, but quite usable, nevertheless. No noticeable jitter, […]

  • Linux on Mediatek MT6235 Phones.

    30.11.2010 ncrmnt

    It’s started. Just give loads of thanks to osmocom-baseband guys who made the initial efforts. Anyway, the whole stuff is working. Even on my old E1000 phone. The instructions are pretty much straightforward. Take your phone Hook it to your favourite uart to usb chip (mine is ftdi) And fire up osmocon and osmoload as […]

  • First take on a DC motor controller.

    22.11.2010 ncrmnt

    Well, that was a hacky weekend. I teamed up with Inky and we went on hacking a small plotter with a multi-axis controller. Apart from finding out what design we could throw up with the parts I had around and salvaging a bunch of stuff from dead pc parts we managed to finish the design […]

  • ChinaPhone + MakeProgress = USB Bus Voltmeter

    27.10.2010 ncrmnt

    It’s been some time already, that I’ve been working on my  ‘Remote Debug Rig’. The whole setup involves a Chinese mobile phone, I use a gsm module, a couple of avrs and other stuff. The whole setup is yet to be described once finished, but one thing I can show off now. Since I use a lot […]

  • madwimax & ap mode

    26.09.2010 ncrmnt

    Well, it took me a while to figure out what was wrong and why the heck my atheros laptop wifi won’t go to AP mode. Looks like the ath5k driver that is in stock ubuntu 10.04 cannot do any AP mode, so you’ll have to grab ath_pci one. However, the snapshots didn’t work at all […]

  • Q&D air conditioner (2.5 hrs to make one!)

    08.08.2010 ncrmnt

    It’s damn hot in Russia now. no… Well, it’s HOT AS HELL HERE. This weekend sitting in my country house with no air conditioner there, I got finally just a bit too sick of it. Besides the heat the smoke from those damned fires is always around. (see photos under the cut) Anyways, I got […]

Posts pagination

Previous 1 … 14 15 16 Next

Language

  • English
  • Русский
Necromancer's notes © 2026 Lulz Driven Development Colophon · RSS · Sitemap